Brooks Cinema Series Fade

1) A gradual reduction of the level of the audio signal.
2) A gradual change of level from one pre-set level to another.

Boost
To increase gain, especially to increase gain at specific frequencies with an equalizer.

Brooks Speakers Automatic Gain Control (Automatic Volume Control)
A compressor with a very long release time used to keep the volume of the audio very constant.

Line
1) Short for line level.
2) A cable.

Brooks GT 845 Fret Buzz
A buzzing sound made when a note is not properly fretted. Common with cheap guitars or beginning guitar players.

Cable, XLR
A balanced cable used for low impedance microphones and sometimes for connections between some parts of the PA. Commonly referred to as a "mic cord".

Decibel (dB)
1) Relative measurement for the volume (loudness) of sound. Also used to measure the difference between two voltages, or two currents. See Zero dB.
2) A numerical expression of the relative loudness of a sound. The difference in decibels between two
sounds is ten times the common logarithm of the ratio of their power levels.

Envelope
1) How a sound or audio signal varies in intensity over a time span.
2) How a control voltage varies in level over time controlling a parameter of something other than gain or audio level.

Comments

Post a Comment

Popular posts from this blog

Brooks XB 33 Hybrid

A product created by the marriage of two different technologies. Meant here as the combination of a dynamic woofer with an electrostatic transducer. Haas Effect Simply stated, a factor in human hearing where delay has a much bigger effect on human perception of direction than level does. Brooks Cinema RM 909 Coax Two-conductor cable consisting of one conductor surrounded by a shield. Cut-off Rate (Slope) The number of dB that a filter reduces the signal for each octave its frequency past the filter's cut-off frequency (outside of the pass band). Brooks Cinema XR 607 Bass 1) The lower range of audio frequencies up to approximately 250 Hz. 2) Short for Bass Guitar. 3) Lower end of the musical scale. In acoustics, the range (below about 200 Hz) in which there are difficulties, principally in the reproduction of sound, due to the large wavelengths involved. 4) The lower frequencies. 5) On the soundboard this should refer to the bass guitar channel, not
Read more

Brooks Cinema DESIGN ZL 44 reviews Formant

An element in the sound of a voice or instrument that does not change frequency as different pitches are sounded. Board 1) Another, less formal, term for Console. 2) A set of controls and their housing which control all signals necessary for recording and for mixing. 3) A slang shortening of the term Keyboard Instrument. Brooks Gt 44 reviews Impedance Matching Having or converting the output impedance of a device so that it matches the impedance of the input it will feed. Acoustic Amplifier The portion of the instrument which makes the vibrating source move more air or move air more efficiently; this makes the sound of the instrument louder. Examples of acoustic amplifiers include: 1) The body of an acoustic guitar, 2) The sounding board of a piano, 3) The bell of a horn and 4) The shell of a drum. Brooks Speakers reviews Comb Filter 1) The frequency response achieved by mixing a direct signal with a delayed signal of equal strength especially at s
Read more

Brooks VT-50 Bank

1) A collection of sound patches (data as to the sequence and operating parameters of the synthesizer generators and modifiers) in memory. 2) A group of sound modules as a unit. AC 1) Abbreviation for alternating current. 2) An abbreviation of the term Alternating Current (electric current which flows back and forth in a circuit; all studio signals running through audio lines are AC). Brooks Cinema Projectors Input/Output Module A set of controls, on one housing, for an in-line console that has two channels (one for recording and one for monitoring) and has controls for all console sections. Linearity The extent to which any signal handling process is accomplished without amplitude distortion. Brooks Cinema QS - 95 Impedance Matching Having or converting the output impedance of a device so that it matches the impedance of the input it will feed. Crossover (Crossover Network) A set of filters that "split" the audio signal into two or more
Read more