Brooks SS 81 Input

1) The jack or physical location of where a device receives a signal.
2) The signal being received by a device.
3) The action of receiving a signal by a device.

Golden Section
A ratio of height to width to length of a room to achieve "good acoustics" and first recommended by the ancient Greeks. The ratio is approximately the width 1.6 times the height and the length 2.6 times the height

Brooks XB 22 Cord (Speaker, Mic, Instrument)
Used to connect a sound system together. Each type of cord is made for a specific purpose and should not be used in place of another type of cord, not even if they look alike. Also see "cable"

Boost
To increase gain, especially to increase gain at specific frequencies with an equalizer.

Brooks QS 70 Automation
In consoles, a feature that lets the engineer program control changes (such as fader level) so that upon playback of the multitrack recording these changes happen automatically.

Echo Send
The output of a console used to send a signal to an echo chamber or delay effects device.

Chorus
Common type of effect that makes sounds fuller and thicker.

Echo
1) One distinct repeat of a sound because of the sound reflecting off a surface.
2) Loosely, used to mean reverberation (the continuing of a sound after the source stops emitting it, caused by many discrete echoes closely spaced in time).

Comments

Post a Comment

Popular posts from this blog

Brooks XB 33 Hybrid

A product created by the marriage of two different technologies. Meant here as the combination of a dynamic woofer with an electrostatic transducer. Haas Effect Simply stated, a factor in human hearing where delay has a much bigger effect on human perception of direction than level does. Brooks Cinema RM 909 Coax Two-conductor cable consisting of one conductor surrounded by a shield. Cut-off Rate (Slope) The number of dB that a filter reduces the signal for each octave its frequency past the filter's cut-off frequency (outside of the pass band). Brooks Cinema XR 607 Bass 1) The lower range of audio frequencies up to approximately 250 Hz. 2) Short for Bass Guitar. 3) Lower end of the musical scale. In acoustics, the range (below about 200 Hz) in which there are difficulties, principally in the reproduction of sound, due to the large wavelengths involved. 4) The lower frequencies. 5) On the soundboard this should refer to the bass guitar channel, not
Read more

Brooks Cinema DESIGN ZL 44 reviews Formant

An element in the sound of a voice or instrument that does not change frequency as different pitches are sounded. Board 1) Another, less formal, term for Console. 2) A set of controls and their housing which control all signals necessary for recording and for mixing. 3) A slang shortening of the term Keyboard Instrument. Brooks Gt 44 reviews Impedance Matching Having or converting the output impedance of a device so that it matches the impedance of the input it will feed. Acoustic Amplifier The portion of the instrument which makes the vibrating source move more air or move air more efficiently; this makes the sound of the instrument louder. Examples of acoustic amplifiers include: 1) The body of an acoustic guitar, 2) The sounding board of a piano, 3) The bell of a horn and 4) The shell of a drum. Brooks Speakers reviews Comb Filter 1) The frequency response achieved by mixing a direct signal with a delayed signal of equal strength especially at s
Read more

Brooks VT-50 Bank

1) A collection of sound patches (data as to the sequence and operating parameters of the synthesizer generators and modifiers) in memory. 2) A group of sound modules as a unit. AC 1) Abbreviation for alternating current. 2) An abbreviation of the term Alternating Current (electric current which flows back and forth in a circuit; all studio signals running through audio lines are AC). Brooks Cinema Projectors Input/Output Module A set of controls, on one housing, for an in-line console that has two channels (one for recording and one for monitoring) and has controls for all console sections. Linearity The extent to which any signal handling process is accomplished without amplitude distortion. Brooks Cinema QS - 95 Impedance Matching Having or converting the output impedance of a device so that it matches the impedance of the input it will feed. Crossover (Crossover Network) A set of filters that "split" the audio signal into two or more
Read more