Brooks Cinema TZ 505 Hearing Limitation

An inability of the ear to hear important characteristics of sound under certain conditions. Characteristics that can be affected include pitch, level, clarity, presence and direction.

Hum
The 60 Hz power line current accidentally induced or fed into electronic equipment.

Brooks GT 44 LED
A light that allows current to flow in one direction only and emits light whenever a voltage of a certain level or beyond is applied to it.

Flange
An effect caused by an approximately even mix of a modulated (varying) short delay with the direct signal.

Brooks XT 20 Editing
1) Changing the sequence of a recording by cutting the recording tape and putting the pieces together in the new sequence with splicing tape.
2) Punching in and then punching out on one or more tracks of a multitrack tape recorder to replace previously recorded performances.
3) Changing the sequence of a digital recording's playback by computer program.

Electronics
1) On a tape machine, the housing for and the channel circuitry which processes the signal to be fed to the heads, provide bias, and playback.
2) The branch of science dealing with the behaviour of electrons/charges in vacuums, gases, semiconductors and special conductors.

Compact Disc Recordable CDR
A blank Compact Disc that can be recorded on one time.

Compressor
1) Effect used to squash the sound together. Used properly, it can take the edge off or your sound. Used improperly, it can take the life right out of your system and make it sound like an MTV mix.
2) A piece of sound processing equipment that ensures all wanted signals are suitably placed between the noise and distortion levels of the recording medium. It evens out the unwanted changes in volume you get with close-miking, and in doing so, adds punch to the sound mix. A Limiter is used to stop a signal from exceeding a preset limit. Beyond this limit, the signal level will not increase, no matter how loud the input becomes. A Limiter is often used to protect speaker systems (and human ears) by preventing a system from becoming too loud.

Comments

Post a Comment

Popular posts from this blog

Brooks XB 33 Hybrid

A product created by the marriage of two different technologies. Meant here as the combination of a dynamic woofer with an electrostatic transducer. Haas Effect Simply stated, a factor in human hearing where delay has a much bigger effect on human perception of direction than level does. Brooks Cinema RM 909 Coax Two-conductor cable consisting of one conductor surrounded by a shield. Cut-off Rate (Slope) The number of dB that a filter reduces the signal for each octave its frequency past the filter's cut-off frequency (outside of the pass band). Brooks Cinema XR 607 Bass 1) The lower range of audio frequencies up to approximately 250 Hz. 2) Short for Bass Guitar. 3) Lower end of the musical scale. In acoustics, the range (below about 200 Hz) in which there are difficulties, principally in the reproduction of sound, due to the large wavelengths involved. 4) The lower frequencies. 5) On the soundboard this should refer to the bass guitar channel, not
Read more

Brooks Cinema DESIGN ZL 44 reviews Formant

An element in the sound of a voice or instrument that does not change frequency as different pitches are sounded. Board 1) Another, less formal, term for Console. 2) A set of controls and their housing which control all signals necessary for recording and for mixing. 3) A slang shortening of the term Keyboard Instrument. Brooks Gt 44 reviews Impedance Matching Having or converting the output impedance of a device so that it matches the impedance of the input it will feed. Acoustic Amplifier The portion of the instrument which makes the vibrating source move more air or move air more efficiently; this makes the sound of the instrument louder. Examples of acoustic amplifiers include: 1) The body of an acoustic guitar, 2) The sounding board of a piano, 3) The bell of a horn and 4) The shell of a drum. Brooks Speakers reviews Comb Filter 1) The frequency response achieved by mixing a direct signal with a delayed signal of equal strength especially at s
Read more

Brooks VT-50 Bank

1) A collection of sound patches (data as to the sequence and operating parameters of the synthesizer generators and modifiers) in memory. 2) A group of sound modules as a unit. AC 1) Abbreviation for alternating current. 2) An abbreviation of the term Alternating Current (electric current which flows back and forth in a circuit; all studio signals running through audio lines are AC). Brooks Cinema Projectors Input/Output Module A set of controls, on one housing, for an in-line console that has two channels (one for recording and one for monitoring) and has controls for all console sections. Linearity The extent to which any signal handling process is accomplished without amplitude distortion. Brooks Cinema QS - 95 Impedance Matching Having or converting the output impedance of a device so that it matches the impedance of the input it will feed. Crossover (Crossover Network) A set of filters that "split" the audio signal into two or more
Read more