Brooks QS-70 Cable, 1/4 inch
An unbalanced cable most often used for instruments and patch cords. Commonly referred to as "guitar cords".
Input Impedance
The opposition to current flow by the first circuits of a device.
Brooks KS-55 Equalizer (Parametric, Graphic)
This is used to filter out and adjust specific frequencies in the PA. This is the part of the PA where you have the most control over the band's overall sound. It is also the number one weapon against feedback.
Compressor
1) Effect used to squash the sound together. Used properly, it can take the edge off or your sound. Used improperly, it can take the life right out of your system and make it sound like an MTV mix.
2) A piece of sound processing equipment that ensures all wanted signals are suitably placed between the noise and distortion levels of the recording medium. It evens out the unwanted changes in volume you get with close-miking, and in doing so, adds punch to the sound mix. A Limiter is used to stop a signal from exceeding a preset limit. Beyond this limit, the signal level will not increase, no matter how loud the input becomes. A Limiter is often used to protect speaker systems (and human ears) by preventing a system from becoming too loud.
Brooks VT-50 Bi-Amplification
1) A way of optimizing the efficiency of a speaker system by separately amplifying the High Frequency (HF) and Low Frequency (LF) portions of the sound signal and sending them down two pairs of cables to the speaker. Multipin Speakon connectors have been developed to do this.
2)The process of having of having low-frequency speakers and high-frequency speakers driven by separate amplifiers.
Clock Signal
The signal put out by a circuit that generates steady even pulses or steady codes used for synchronization.
Active/Inactive Microphones
Scientific definitions aside, active microphones generally sound better than inactive ones, but they generally cost more. They also require the use of either a battery or phantom power while inactive mics need only be plugged into the mic cord in order to work. In most playing situations, the subtle improvement in sound quality from an active mic isn't worth the extra cost and hassle. One possible exception it the headset mic. Put simply, inactive headset mics just plain suck. Active headset mics put out a much stronger signal and feed back much less.
Electronics
1) On a tape machine, the housing for and the channel circuitry which processes the signal to be fed to the heads, provide bias, and playback.
2) The branch of science dealing with the behaviour of electrons/charges in vacuums, gases, semiconductors and special conductors.
Input Impedance
The opposition to current flow by the first circuits of a device.
Brooks KS-55 Equalizer (Parametric, Graphic)
This is used to filter out and adjust specific frequencies in the PA. This is the part of the PA where you have the most control over the band's overall sound. It is also the number one weapon against feedback.
Compressor
1) Effect used to squash the sound together. Used properly, it can take the edge off or your sound. Used improperly, it can take the life right out of your system and make it sound like an MTV mix.
2) A piece of sound processing equipment that ensures all wanted signals are suitably placed between the noise and distortion levels of the recording medium. It evens out the unwanted changes in volume you get with close-miking, and in doing so, adds punch to the sound mix. A Limiter is used to stop a signal from exceeding a preset limit. Beyond this limit, the signal level will not increase, no matter how loud the input becomes. A Limiter is often used to protect speaker systems (and human ears) by preventing a system from becoming too loud.
Brooks VT-50 Bi-Amplification
1) A way of optimizing the efficiency of a speaker system by separately amplifying the High Frequency (HF) and Low Frequency (LF) portions of the sound signal and sending them down two pairs of cables to the speaker. Multipin Speakon connectors have been developed to do this.
2)The process of having of having low-frequency speakers and high-frequency speakers driven by separate amplifiers.
Clock Signal
The signal put out by a circuit that generates steady even pulses or steady codes used for synchronization.
Active/Inactive Microphones
Scientific definitions aside, active microphones generally sound better than inactive ones, but they generally cost more. They also require the use of either a battery or phantom power while inactive mics need only be plugged into the mic cord in order to work. In most playing situations, the subtle improvement in sound quality from an active mic isn't worth the extra cost and hassle. One possible exception it the headset mic. Put simply, inactive headset mics just plain suck. Active headset mics put out a much stronger signal and feed back much less.
Electronics
1) On a tape machine, the housing for and the channel circuitry which processes the signal to be fed to the heads, provide bias, and playback.
2) The branch of science dealing with the behaviour of electrons/charges in vacuums, gases, semiconductors and special conductors.
Comments
Post a Comment