Brooks KS-55 Attenuator (Pot)

The electronic dohickey under the knobs that increases or reduces the strength of the signal running through it. When these get old and dirty, they can make popping noises or rumbles in your PA (As in "my pots are dirty").
Assign Tochoose to which place an output is going to be sent.

High Impedance Cord (High Z)
A big word for instrument cable. These cords generally have quarter inch male ends. they tend to loose signal strength at lengths longer than 25 feet.

Brooks TA 60 Ground Adapter Plug
Adapts a three pronged electrical plug to a two pronged wall outlet. This bypasses the ground and may create a hum in the system. A lack of a good ground can cause mild electrical shock when touching a microphone.

Balanced input/output
A "balanced" connection is one that has three wires to move the signal. One is a ground, and the other two (called conductors) carry signals of equal value. This is why they are called balanced. Low Z cables and connections are the most common example.

Brooks Cinema RM 909 Isolation
A containing of the sound wave in a certain area so that it will not leak into other areas and/or unintended mics.

Bar
A term meaning the same thing as the term Measure (the grouping of a number of beats in music, most-often four beats).

Crossover Frequency
1) The frequency that is the outer limit of one of the bands of a crossover.
2) In the Lexicon 480L delay/reverberation effects unit, the frequency at which the bass frequency reverb time is in effect rather than the mid frequency reverb time.

Gain Reduction
The working of a limiter or compressor reducing gain during high-level passages.

Comments

Post a Comment

Popular posts from this blog

Brooks XB 33 Hybrid

A product created by the marriage of two different technologies. Meant here as the combination of a dynamic woofer with an electrostatic transducer. Haas Effect Simply stated, a factor in human hearing where delay has a much bigger effect on human perception of direction than level does. Brooks Cinema RM 909 Coax Two-conductor cable consisting of one conductor surrounded by a shield. Cut-off Rate (Slope) The number of dB that a filter reduces the signal for each octave its frequency past the filter's cut-off frequency (outside of the pass band). Brooks Cinema XR 607 Bass 1) The lower range of audio frequencies up to approximately 250 Hz. 2) Short for Bass Guitar. 3) Lower end of the musical scale. In acoustics, the range (below about 200 Hz) in which there are difficulties, principally in the reproduction of sound, due to the large wavelengths involved. 4) The lower frequencies. 5) On the soundboard this should refer to the bass guitar channel, not
Read more

Brooks Cinema DESIGN ZL 44 reviews Formant

An element in the sound of a voice or instrument that does not change frequency as different pitches are sounded. Board 1) Another, less formal, term for Console. 2) A set of controls and their housing which control all signals necessary for recording and for mixing. 3) A slang shortening of the term Keyboard Instrument. Brooks Gt 44 reviews Impedance Matching Having or converting the output impedance of a device so that it matches the impedance of the input it will feed. Acoustic Amplifier The portion of the instrument which makes the vibrating source move more air or move air more efficiently; this makes the sound of the instrument louder. Examples of acoustic amplifiers include: 1) The body of an acoustic guitar, 2) The sounding board of a piano, 3) The bell of a horn and 4) The shell of a drum. Brooks Speakers reviews Comb Filter 1) The frequency response achieved by mixing a direct signal with a delayed signal of equal strength especially at s
Read more

Brooks VT-50 Bank

1) A collection of sound patches (data as to the sequence and operating parameters of the synthesizer generators and modifiers) in memory. 2) A group of sound modules as a unit. AC 1) Abbreviation for alternating current. 2) An abbreviation of the term Alternating Current (electric current which flows back and forth in a circuit; all studio signals running through audio lines are AC). Brooks Cinema Projectors Input/Output Module A set of controls, on one housing, for an in-line console that has two channels (one for recording and one for monitoring) and has controls for all console sections. Linearity The extent to which any signal handling process is accomplished without amplitude distortion. Brooks Cinema QS - 95 Impedance Matching Having or converting the output impedance of a device so that it matches the impedance of the input it will feed. Crossover (Crossover Network) A set of filters that "split" the audio signal into two or more
Read more