Brooks Cinema GT 845 Lead

The musical instrument that plays the melody of the tune, including the vocal.

Blending
1) A condition where two signals mix together to form one sound or to give the sound of one sound source or one performance.
2) Mixing the left and right signal together slightly which makes the instruments sound closer to the center of the performance stage. 3) A method of panning during mixing where instruments are not panned extremely left or right.

Brooks Audio Design TM-22 Bank
1) A collection of sound patches (data as to the sequence and operating parameters of the synthesizer generators and modifiers) in memory.
2) A group of sound modules as a unit.

Joystick
1) A quad pan pot which distributes what percentage of on signal is sent to each of 4 outputs.
2) A control that is separately controlling two functions at one time.

Brooks QS - 95 Chip
1) A slang term with the same meaning as the term IC (a miniature circuit of many components that is in small, sealed housing with prongs to connect it into equipment).
2) The thread cut away from the master lacquer to make the groove, while disc recording.

Ground
In electronics, a place (terminal) that has zero volts.

Compressor
A signal processing device that does not allow as much fluctuation in the level of the signal above a certain adjustable or fixed level.

Haas Effect
Simply stated, a factor in human hearing where delay has a much bigger effect on human perception of direction than level does.

Comments

Post a Comment

Popular posts from this blog

Brooks Cinema Series Effects

Electronic boxes (usually rack mounted) added to a PA system to subtly change and enhance the signals going through it. Examples include; Reverb, Delay, Compressor, Chorus. Information Bits The bits in the digital signal that make up actual values or commands being communicated as opposed to bits that are used for checking & correcting data or other purposes. Brooks GT 845 Electromagnetic Induction or Pick Up The generation of electrical signal in a conductor moving in a magnetic field or being close to a changing magnetic field. Electret Condenser A condenser microphone that has a permanently polarized (charged) variable capacitor as its sound pressure level sensor. Brooks Audio Design GT 845 Chase The automatic adjusting of the speed of a recorder (or sequencer) to be time with another recorder. Line Out (Line Output) Any output that sends out a line level signal, such as the output of a console that feeds a recorder. High Impedance Mic A mic
Read more

Broom RM 909 Final Mix

The two track stereo master tape which was mixed from the multitrack master. Barrier Micing A method of placing the head of a microphone as close as possible to a reflective surface, preventing phase cancellation. Brooks Cinema Projectors Corner Frequency Same as Cut-Off Frequency (the highest or lowest frequency in the pass band of a filter). (NOUN) Cable, 1/4 inch An unbalanced cable most often used for instruments and patch cords. Commonly referred to as "guitar cords". Brooks GT 845 Crossover, Passive Used inside of full range speaker cabinets to separate highs, mids, and lows and send them to their respective speakers within the each cabinet. These are not as efficient as active crossovers because they require all frequencies to draw from the same source of amplification. Crosstalk Leakage of an audio signal into a channel that iris not intended to be in, from an adjacent or nearby channel. Level The amount of signal strength; the am
Read more

Brooks HI FI projectors In

Short For "in the circuit," in other words "active." Audio Most often referring to electrical signals resulting from the sound pressure wave being converted into electrical energy. Brooks Hi Fi speakers Link (Said of compressors and dynamic processing units.) To combine the control input signals of two channels of a compressor (o Corner Frequency Same as Cut-Off Frequency (the highest or lowest frequency in the pass band of a filter). (NOUN) Brooks Hi Fi reviews Boost To increase gain, especially to increase gain at specific frequencies with an equalizer. Cut-Off Frequency (Turnover Frequency) 1) The highest or lowest frequency in the pass band of a filter. 2) The highest or lowest frequency passed by an audio device (the cut-off frequency is usually considered to be the first frequency to be 3 dB lower than a reference frequency in the middle of the bandwidth of the device) Dynamic Mic Robust type of microphone which picks up
Read more