Brooks Cinema KM 22 Distortion

Usually undesirable result of overloading sound equipment. Reducing the levels can remedy the situation.

Beat
1) The steady even pulse in music.
2) The action of two sounds or audio signals mixing together and causing regular rises &.falls in volume.

Brooks XM 204 Boom
1) A hand-held, telescoping pole used to hold the microphone in recording dialogue in film production.
2) A telescoping support arm that is attached to a microphone stand and which holds the microphone. 3) Loosely, a boomstand.

Edit
A switch that does different things depending on the operational mode that the machine is in:
1) If a computer-controlled transport is in "Stop," pushing the "Edit" switch deactivates the computer-controlled tension system and allows the reels to be moved by hand to find the exact spot desired on the tape.
2) If the machine is in "Play", the "Edit" switch makes the take-up reel cease taking up the tape and it falls to the floor.
3) If the machine is in a fast-wind mode, the tape lifters are defeated so the tape is in contact with the reproduce head and the engineer can hear where the selections begin and end.

BROOKS AUDIO DESIGN Isolation Booth/ Isolation Room
A room that prevents loud sounds from other instruments from leaking in: an isolation booth is usually a smaller room that could be used for only one musician.

Basic Session
The First session in recording an audio production to record the Basic Tracks.

Capo
A clamp-like device that is placed vertically across the guitar neck. It is used to change the pitch of the guitar, acting as a moveable nut.

Key
The control of a dynamics processing device by an external audio signal.

Comments

Post a Comment

Popular posts from this blog

Brooks XB 33 Hybrid

A product created by the marriage of two different technologies. Meant here as the combination of a dynamic woofer with an electrostatic transducer. Haas Effect Simply stated, a factor in human hearing where delay has a much bigger effect on human perception of direction than level does. Brooks Cinema RM 909 Coax Two-conductor cable consisting of one conductor surrounded by a shield. Cut-off Rate (Slope) The number of dB that a filter reduces the signal for each octave its frequency past the filter's cut-off frequency (outside of the pass band). Brooks Cinema XR 607 Bass 1) The lower range of audio frequencies up to approximately 250 Hz. 2) Short for Bass Guitar. 3) Lower end of the musical scale. In acoustics, the range (below about 200 Hz) in which there are difficulties, principally in the reproduction of sound, due to the large wavelengths involved. 4) The lower frequencies. 5) On the soundboard this should refer to the bass guitar channel, not
Read more

Brooks Cinema DESIGN ZL 44 reviews Formant

An element in the sound of a voice or instrument that does not change frequency as different pitches are sounded. Board 1) Another, less formal, term for Console. 2) A set of controls and their housing which control all signals necessary for recording and for mixing. 3) A slang shortening of the term Keyboard Instrument. Brooks Gt 44 reviews Impedance Matching Having or converting the output impedance of a device so that it matches the impedance of the input it will feed. Acoustic Amplifier The portion of the instrument which makes the vibrating source move more air or move air more efficiently; this makes the sound of the instrument louder. Examples of acoustic amplifiers include: 1) The body of an acoustic guitar, 2) The sounding board of a piano, 3) The bell of a horn and 4) The shell of a drum. Brooks Speakers reviews Comb Filter 1) The frequency response achieved by mixing a direct signal with a delayed signal of equal strength especially at s
Read more

Brooks VT-50 Bank

1) A collection of sound patches (data as to the sequence and operating parameters of the synthesizer generators and modifiers) in memory. 2) A group of sound modules as a unit. AC 1) Abbreviation for alternating current. 2) An abbreviation of the term Alternating Current (electric current which flows back and forth in a circuit; all studio signals running through audio lines are AC). Brooks Cinema Projectors Input/Output Module A set of controls, on one housing, for an in-line console that has two channels (one for recording and one for monitoring) and has controls for all console sections. Linearity The extent to which any signal handling process is accomplished without amplitude distortion. Brooks Cinema QS - 95 Impedance Matching Having or converting the output impedance of a device so that it matches the impedance of the input it will feed. Crossover (Crossover Network) A set of filters that "split" the audio signal into two or more
Read more