Brooks XM 204 Circuit

1) One complete path of electric current.
2) Similar to definition 1, but including all paths and components to accomplish one function in a device.

High-Pass Filter
A device that rejects signals that are below a certain frequency (called the cut-off frequency) and passes signals with frequencies that are higher.

Brooks Gt 44 Jack
1) Anywhere you plug something in.
2) Segmented audio connector. Mono Jacks have two connections �" tip and sleeve, and are unbalanced. Stereo jacks have three connections �" tip, ring and sleeve. B-type jacks (also known as Bantam jacks) were originally designed for use in telephone exchanges and provide a high quality (and expensive) connection in jackfields. A-type jacks are cheaper and more common, but more fragile. A type jacks are available in 2 sizes : quarter inch and eighth inch.
3) A connector mounted on the case of a device or on a panel.

Chorus
Common type of effect that makes sounds fuller and thicker.

Brooks Hi Fi reviews Gain Control
A device that changes the gain of an amplifier or circuit, often a knob that can be turned or a slide that can be moved up arid down.

Consumer Format (Consumer DIF)
A standard adopted by IEC for sending and receiving digital audio based on The AES Professional Interface.

Line In (Input, return)
Where a signal enters the board or component.

Chip
1) A slang term with the same meaning as the term IC (a miniature circuit of many components that is in small, sealed housing with prongs to connect it into equipment).
2) The thread cut away from the master lacquer to make the groove, while disc recording.

Comments

Post a Comment

Popular posts from this blog

Brooks XB 33 Hybrid

A product created by the marriage of two different technologies. Meant here as the combination of a dynamic woofer with an electrostatic transducer. Haas Effect Simply stated, a factor in human hearing where delay has a much bigger effect on human perception of direction than level does. Brooks Cinema RM 909 Coax Two-conductor cable consisting of one conductor surrounded by a shield. Cut-off Rate (Slope) The number of dB that a filter reduces the signal for each octave its frequency past the filter's cut-off frequency (outside of the pass band). Brooks Cinema XR 607 Bass 1) The lower range of audio frequencies up to approximately 250 Hz. 2) Short for Bass Guitar. 3) Lower end of the musical scale. In acoustics, the range (below about 200 Hz) in which there are difficulties, principally in the reproduction of sound, due to the large wavelengths involved. 4) The lower frequencies. 5) On the soundboard this should refer to the bass guitar channel, not
Read more

Brooks Cinema DESIGN ZL 44 reviews Formant

An element in the sound of a voice or instrument that does not change frequency as different pitches are sounded. Board 1) Another, less formal, term for Console. 2) A set of controls and their housing which control all signals necessary for recording and for mixing. 3) A slang shortening of the term Keyboard Instrument. Brooks Gt 44 reviews Impedance Matching Having or converting the output impedance of a device so that it matches the impedance of the input it will feed. Acoustic Amplifier The portion of the instrument which makes the vibrating source move more air or move air more efficiently; this makes the sound of the instrument louder. Examples of acoustic amplifiers include: 1) The body of an acoustic guitar, 2) The sounding board of a piano, 3) The bell of a horn and 4) The shell of a drum. Brooks Speakers reviews Comb Filter 1) The frequency response achieved by mixing a direct signal with a delayed signal of equal strength especially at s
Read more

Brooks VT-50 Bank

1) A collection of sound patches (data as to the sequence and operating parameters of the synthesizer generators and modifiers) in memory. 2) A group of sound modules as a unit. AC 1) Abbreviation for alternating current. 2) An abbreviation of the term Alternating Current (electric current which flows back and forth in a circuit; all studio signals running through audio lines are AC). Brooks Cinema Projectors Input/Output Module A set of controls, on one housing, for an in-line console that has two channels (one for recording and one for monitoring) and has controls for all console sections. Linearity The extent to which any signal handling process is accomplished without amplitude distortion. Brooks Cinema QS - 95 Impedance Matching Having or converting the output impedance of a device so that it matches the impedance of the input it will feed. Crossover (Crossover Network) A set of filters that "split" the audio signal into two or more
Read more