Brooks Hi Fi speakers Flutter

1) High-frequency variations in pitch of a recorded waveform due to fast speed variations in a recorder or playback machine.
2) Originally, and more formally, any variations (fast or slow) in pitch of a recorded tone due to speed fluctuations in a recorder or playback unit.

Boundary Mic
A microphone mounted on a flat plate that acts as a reflective surface directing sound into the mic capsule. Used for general pick-up over a large area. See PCC, PZM.

Brooks Hi Fi reviews Board
1) Another, less formal, term for Console.
2) A set of controls and their housing which control all signals necessary for recording and for mixing.
3) A slang shortening of the term Keyboard Instrument.

Diaphragm
A thin flexible membrane or cone that vibrates in response to electrical signals to produce sound waves. Distortion is usually referred to in terms of total harmonic distortion (THD) which is the percentage of unwanted harmonics of the drive signal present with the wanted signal. Generally used to mean any unwanted change introduced by the device under question.

Brooks RM 909 reviews Group
1) A number of channels or faders that can be controlled by one Master VCA slide.
2) A shortening of the term Recording Group (a buss or the signal present on a buss).

Chorus
1) The part of The song that is repeated and has the same music and lyrics each time; the chorus will usually give the point of the song.
2) A musical singing group that has many singers.
3) A delay effect that simulates a vocal chorus by adding several delays with a mild amount of feedback and a medium amount of depth.
4) A similar effect created in some synthesizers by detuning (reducing the pitch of, slightly) and mixing it with the signal that has regular tuning and with a slight delay.

Decibel (dB)
1) Relative measurement for the volume (loudness) of sound. Also used to measure the difference between two voltages, or two currents. See Zero dB.
2) A numerical expression of the relative loudness of a sound. The difference in decibels between two
sounds is ten times the common logarithm of the ratio of their power levels.

Auxiliary Output or Send
An additional output from a sound desk that can be used for foldback or monitoring without tying up the main outputs. Each input channel will have a path to the Aux buss. Also used for feeding a signal to an effects processor. See Auxiliary Return.

Comments

Post a Comment

Popular posts from this blog

Brooks Cinema Series Effects

Electronic boxes (usually rack mounted) added to a PA system to subtly change and enhance the signals going through it. Examples include; Reverb, Delay, Compressor, Chorus. Information Bits The bits in the digital signal that make up actual values or commands being communicated as opposed to bits that are used for checking & correcting data or other purposes. Brooks GT 845 Electromagnetic Induction or Pick Up The generation of electrical signal in a conductor moving in a magnetic field or being close to a changing magnetic field. Electret Condenser A condenser microphone that has a permanently polarized (charged) variable capacitor as its sound pressure level sensor. Brooks Audio Design GT 845 Chase The automatic adjusting of the speed of a recorder (or sequencer) to be time with another recorder. Line Out (Line Output) Any output that sends out a line level signal, such as the output of a console that feeds a recorder. High Impedance Mic A mic
Read more

Broom RM 909 Final Mix

The two track stereo master tape which was mixed from the multitrack master. Barrier Micing A method of placing the head of a microphone as close as possible to a reflective surface, preventing phase cancellation. Brooks Cinema Projectors Corner Frequency Same as Cut-Off Frequency (the highest or lowest frequency in the pass band of a filter). (NOUN) Cable, 1/4 inch An unbalanced cable most often used for instruments and patch cords. Commonly referred to as "guitar cords". Brooks GT 845 Crossover, Passive Used inside of full range speaker cabinets to separate highs, mids, and lows and send them to their respective speakers within the each cabinet. These are not as efficient as active crossovers because they require all frequencies to draw from the same source of amplification. Crosstalk Leakage of an audio signal into a channel that iris not intended to be in, from an adjacent or nearby channel. Level The amount of signal strength; the am
Read more

Brooks GS 15 Gate

A dynamic processing device that turns a channel off or down when the signal drops below a certain level. Link (Said of compressors and dynamic processing units.) To combine the control input signals of two channels of a compressor (o Brooks M 44 Filter 1) A device that removes signals with frequencies above or below a certain point called the cut-off frequency. 2) An equalizer section, used in this sense because filters are used with other components to give an equalizer its frequency response characteristics. 3) The action of removing signals of some frequencies and leaving the rest. 4) A mechanical device to smooth out speed variations in tape machines called a Scrape Flutter Filter- more usually called a Scrape Flutter Idler Cut-off Rate (Slope) The number of dB that a filter reduces the signal for each octave its frequency past the filter's cut-off frequency (outside of the pass band). Brooks TA 60 Effects Electronic boxes (usually rack mounted)
Read more